At dusk, street lamps switch on by themselves, an electronic thermometer measures your temperature, and a smartphone processor runs billions of tiny electronic switches. At the heart of all of them are semiconductors — substances such as silicon and germanium. In conductivity they lie between metals and insulators, but their key feature is different: their resistance depends very strongly on temperature, light and impurities. The formulas from the lesson «Electric current and Ohm's law» still work here — the resistance is simply no longer constant.
How does resistance depend on temperature?
A metal always has plenty of free electrons. Heating hardly changes their number, but the ions of the crystal lattice vibrate harder and get in the electrons’ way more often — the metal’s resistance increases. In a semiconductor there are few free charge carriers at low temperature; heating quickly increases their number, so the resistance decreases. This difference is the main sign of a semiconductor.
Where
- R
- resistance of a metal conductor at t °C, Ω
- R₀
- resistance at 0 °C, Ω
- α
- temperature coefficient of resistance, K⁻¹; for metals α > 0 (about 4 · 10⁻³ K⁻¹ for pure metals)
For metals the resistance grows linearly with temperature. The formula does not apply to semiconductors: their resistance falls sharply and non-linearly when heated.
Example 1: a metal and a thermistor
Problem
1) A copper wire has a resistance of 20 Ω at 0 °C, α = 4 · 10⁻³ K⁻¹. What is its resistance at 100 °C?
2) The tungsten filament of a lamp has 30 Ω at 0 °C, α = 5 · 10⁻³ K⁻¹. What is its resistance at 2000 °C?
3) A semiconductor thermistor has 10 kΩ at 20 °C and 1 kΩ at 80 °C. By what factor does the copper wire’s resistance change for the same heating (20 °C → 80 °C)? Compare.
Show solutionHide solution
Solution
2) R = 30 · (1 + 5 · 10⁻³ · 2000) = 30 · 11 = 330 Ω — 11 times the cold value. That is why a very large current flows at the moment a lamp is switched on, and lamps often burn out at exactly that moment.
3) Copper: R₈₀ / R₂₀ = (1 + 0.32) / (1 + 0.08) ≈ 1.22 — only 22 % more. The thermistor drops 10 times. A semiconductor is far more sensitive to temperature than a metal.
Interactive
The reason lies in the crystal structure. A silicon atom has 4 electrons in its outer shell; in the crystal each atom forms electron-pair (covalent) bonds with 4 neighbours. At very low temperature all electrons are “locked” in bonds and the crystal behaves like an insulator. Heating (or light) breaks some bonds: an electron becomes free and leaves behind an empty place — a hole.
HoleDefinition
The empty place of an electron in a broken covalent bond. When a neighbouring electron jumps into it, the hole “moves”; in an electric field it moves along the field like a particle of charge +e.
Intrinsic conductionDefinition
Conduction of a pure (undoped) semiconductor by equal numbers of free electrons and holes. In a field electrons move against the field and holes along it; temperature and light increase the number of electron–hole pairs.
Impurity conduction: n-type and p-type semiconductors
Adding a tiny amount of another element to pure silicon increases its conductivity many times. A donor atom (valence 5: phosphorus, arsenic, antimony) uses 4 of its 5 electrons for bonds, and the fifth easily becomes free — an n-type semiconductor. An acceptor atom (valence 3: boron, aluminium, gallium, indium) lacks one electron for a bond; it “takes” an electron from a neighbour, leaving a hole there — a p-type semiconductor. Both crystals are neutral as a whole: the current is simply carried mainly by one kind of carrier.
| Type | Impurity | Majority carriers | Minority |
|---|---|---|---|
| n-type | donor, valence 5 (P, As, Sb) | electrons | holes |
| p-type | acceptor, valence 3 (B, Al, Ga, In) | holes | electrons |
Interactive
Example 2 (multiple choice): a p-type semiconductor
Problem
Which impurity added to germanium gives a p-type semiconductor?
A) arsenic B) phosphorus C) indium D) antimony E) silicon
Show solutionHide solution
Solution
Arsenic, phosphorus and antimony are in group V (donors → n-type). Silicon is in group IV like germanium: it gives 4 electrons to bonds and creates no carriers.
Example 3 (multiple choice): I–II–III statements
Problem
Which statements are true?
I. Heating pure silicon decreases its resistance.
II. In an n-type semiconductor the majority carriers are holes.
III. Adding phosphorus to silicon gives an n-type semiconductor.
A) only I B) only II C) I and III D) II and III E) I, II, III
Show solutionHide solution
Solution
II is false: in n-type the majority carriers are electrons.
III is true: phosphorus is a pentavalent donor.
Answer: C (I and III).
The p–n junction and the semiconductor diode
Make one part of a crystal p-type and the other n-type. At the boundary, electrons from the n-part diffuse into the p-part and holes from the p-part into the n-part, and they recombine: an electron “fills” a hole. A thin depletion (barrier) layer, emptied of carriers, forms at the boundary: fixed positive ions stay on the n-side and negative ions on the p-side. Their field stops further crossing of carriers. This boundary is called a p–n junction.
- Forward connection (forward bias): the “+” terminal of the source to the p-part, “−” to the n-part. The external field narrows the depletion layer, majority carriers cross easily — low resistance, large current.
- Reverse connection (reverse bias): “+” to the n-part, “−” to the p-part. The depletion layer widens, only a few minority carriers cross — the current is tiny, practically zero.
Semiconductor diodeDefinition
A device with one p–n junction that lets current pass mainly in one direction (one-way conduction). It is used to rectify alternating current (turn it into direct current) and to protect circuits from wrong polarity; light-emitting diodes (LEDs) give out light when forward-biased.
The diode’s current–voltage characteristic — its I(U) graph — is not a straight line. In the forward direction the current is very weak at small voltages; above about 0.6–0.7 V for silicon (0.2–0.3 V for germanium) it rises steeply. In the reverse direction the current is tiny and stays almost the same until the voltage is very large (breakdown). So a diode does not obey Ohm’s law: its “resistance” U / I depends on the voltage.
Example 4: spotting the diode in a table
Problem
A student measured the current through two components.
U (V): 0.2; 0.4; 0.6; 0.8.
Component 1, I (mA): 2; 4; 6; 8.
Component 2, I (mA): 0; 0.1; 5; 60.
Which one is a resistor and which is a forward-biased diode? Explain.
Show solutionHide solution
Solution
Component 2: U / I = 0.4 / 0.0001 = 4000 Ω; 0.6 / 0.005 = 120 Ω; 0.8 / 0.06 ≈ 13 Ω — the resistance falls sharply as the voltage rises, and the current shoots up after 0.6 V: a forward-biased silicon diode.
Example 5: a diode and a resistor in series
Problem
A silicon diode and a 100 Ω resistor are connected in series to a 5 V source, with the diode forward-biased; the voltage across the conducting diode is 0.7 V.
1) Find the current.
2) If the diode is reversed, what are the current and the voltage across the resistor?
Show solutionHide solution
Solution
2) Reversed, the diode is “closed”: I ≈ 0, the resistor’s voltage I · R ≈ 0, and the whole 5 V is across the diode.
Example 6: which lamp lights up?
Problem
Two branches are connected in parallel to a battery: branch 1 has lamp L₁ and a forward-biased diode D₁, branch 2 has lamp L₂ and a reverse-biased diode D₂. Which lamp lights up? What happens if the battery is turned round?
Show solutionHide solution
Solution
With the battery reversed, D₁ is reverse-biased and D₂ forward-biased — now only L₂ lights up.
On alternating current the lamps would light in turn (each in its own half-period) — this is the rectifying property of a diode.
Thermistor, photoresistor, thermocouple and transistor
- Thermistor — a semiconductor resistor whose resistance depends strongly on temperature; heating lowers its resistance. Used in electronic thermometers, fire alarms and temperature control of motors and batteries.
- Photoresistor — a semiconductor resistor whose resistance falls when it is lit: light breaks covalent bonds and creates electron–hole pairs (the internal photoelectric effect). Used in automatic street lighting and light meters.
- Thermocouple (thermoelement) — two different metals or semiconductors are joined; when the junctions are at different temperatures an EMF appears in the circuit and grows with the temperature difference. In metal thermocouples it is usually tens of microvolts per degree; they measure high temperatures in furnaces. Semiconductor thermoelements give several times more EMF and can work as small generators.
- Transistor — a device with two p–n junctions (n–p–n or p–n–p) and three regions: emitter, base and collector. A small base current controls a collector current tens to hundreds of times larger, so the transistor works as an amplifier and an electronic switch.
Circuit tasks: heating a thermistor, lighting a photoresistor
DİM group I free written tasks ask: “How do the meter readings change when the thermistor is heated (the photoresistor is lit)? Justify your answer with formulas.” The answer is built as a chain: the element’s resistance → total resistance → current → voltages. The most common circuit is this: a constant-voltage source, a resistor R and a thermistor Rₜ in series, an ammeter; voltmeter V₁ is across the resistor and V₂ across the thermistor.
Where
- I
- current in the circuit (ammeter reading), A
- U
- constant source voltage, V
- R, Rₜ
- resistance of the fixed resistor and of the thermistor (photoresistor), Ω
- U₁, U₂
- readings of V₁ (across the resistor) and V₂ (across the thermistor), V
In a series circuit the voltage is shared in proportion to the resistances: U₂ / U₁ = Rₜ / R. The element whose resistance drops gets a smaller share of the voltage.
The element’s resistance
Heating lowers a thermistor’s resistance, light lowers a photoresistor’s (a metal wire’s rises when heated).
Total resistance
In series R + Rₜ decreases too.
Current
I = U / (R + Rₜ) increases → the ammeter reading rises.
Fixed resistor
U₁ = I · R increases → V₁ rises.
The element
U₂ = U − U₁ decreases → V₂ falls (U is constant).
Example 7 (written task): lighting a photoresistor
Problem
A photoresistor, a resistor and an ammeter are connected in series to a constant-voltage source; voltmeter V₁ is across the resistor and V₂ across the photoresistor. How do the readings of the ammeter and the voltmeters change when the photoresistor is lit? Justify with formulas.
Show solutionHide solution
Solution
1) The photoresistor is a semiconductor: light creates electron–hole pairs, so its resistance Rf decreases.
2) The circuit resistance R + Rf decreases, and since U = const, I = U / (R + Rf) increases — the ammeter reading rises.
3) The resistor’s voltage U₁ = I · R increases — V₁ rises.
4) U₁ + U₂ = U = const, so U₂ = U − U₁ decreases — V₂ falls.
For full marks, all three meters must be covered, each with its formula.
Example 8 (coded answer): with numbers
Problem
In the circuit shown, U = 12 V and R = 20 Ω. The thermistor has 100 Ω at 20 °C and 20 Ω at 80 °C. By how many volts does the reading of voltmeter V₂ fall when the thermistor is heated from 20 °C to 80 °C?
Show solutionHide solution
Solution
80 °C: I = 12 / (20 + 20) = 0.3 A; U₁ = 0.3 · 20 = 6 V; U₂ = 12 − 6 = 6 V.
V₂ falls by 10 − 6 = 4 V. Answer: 4. The current and V₁ tripled — the same pattern as in Example 7.
Example 9 (multiple choice): parallel branches
Problem
A lamp and a photoresistor are connected in parallel to an ideal source (no internal resistance); the ammeter is in the unbranched part. How do the ammeter reading and the lamp’s brightness change when the photoresistor is lit?
A) increases; unchanged B) increases; increases C) decreases; unchanged D) decreases; decreases E) unchanged; increases
Show solutionHide solution
Solution
Lamp: IL = U / RL is unchanged → the brightness does not change.
Photoresistor: Rf decreases → If = U / Rf increases.
Ammeter: I = IL + If increases. Answer: A.
(With an internal resistance the voltage would drop a little and the lamp would dim — DİM says so explicitly in the task.)
Remember
- A semiconductor’s resistance falls when it is heated or lit; a metal’s rises with temperature: R = R₀ · (1 + α · t).
- In intrinsic conduction electrons and holes are equal in number; a donor (valence 5) gives n-type, an acceptor (valence 3) gives p-type.
- A p–n junction conducts in forward bias (“+” to p) and hardly at all in reverse; the diode’s I–U curve is non-linear.
- Thermistor: T↑ → R↓; photoresistor: light ↑ → R↓; thermocouple: temperature difference → EMF; transistor: a small base current controls a large collector current.
- In a series circuit, when Rₜ falls: I = U / (R + Rₜ) rises, U₁ = I · R rises, U₂ = U − U₁ falls.