Statics: moment of force, levers, pulleys, inclined plane

Learn the arm and moment of a force, the two conditions of equilibrium, the rule of moments, a beam on two supports, the centre of gravity and types of equilibrium, pulleys, the inclined plane, the golden rule of mechanics and efficiency — with DİM-style tasks.

  • Grades 7 and 10
  • 25 min
  • 12 questions
  • Lesson 14 of 44

In this lesson you will learn

  • Find the arm and the moment of a force and apply the two conditions of equilibrium (ΣF = 0, ΣM = 0)
  • Solve lever and beam-on-two-supports problems with the rule of moments
  • Locate the centre of gravity and tell the types of equilibrium apart
  • Calculate the gain in force, apply the golden rule and find the efficiency of pulleys and the inclined plane

Push a door near its hinges and it hardly moves; push it at the handle and it swings open easily. The force is the same — what differs is how far from the axis of rotation it acts. Simple machines such as the lever, the pulley and the inclined plane rest on this idea: they let a small force lift a large load. In this lesson you will learn when a body stays in equilibrium (this is what statics studies) and how simple machines give a gain in force. The 2026 entrance exam also contained a lever task.

Arm and moment of a force

A rigid body can turn about a fixed axis (a door, a spanner, a lever). The turning effect of a force depends not only on its size but also on its arm.

Arm of a force (d)Definition

the shortest distance from the axis of rotation (the pivot) to the line of action of the force, i.e. the length of the perpendicular dropped from the axis to that line. If the line of action passes through the axis, the arm is zero and the force does not turn the body.

M = F · d

Where

M
moment of the force (torque), in N · m
F
magnitude of the force, in N
d
arm of the force, in m; if the force acts at the end of a rod of length l at an angle α to the rod, d = l · sin α

A moment that turns the body anticlockwise is taken as positive, a clockwise one as negative (this is a convention).

Example 1: three uses of the moment of force

Problem

1) A force of 40 N is applied to a spanner perpendicular to it, 25 cm from the axis of the nut. Find the moment of the force.
2) A moment of 6 N · m is needed to open a door. The handle is 75 cm from the hinges. What force perpendicular to the door must be applied at the handle? And if you push 15 cm from the hinges?
3) A force of 40 N acts at the end of a 0.5 m spanner at an angle of 30° to it. Find the arm and the moment.

Show solutionHide solution

Solution

1) M = F · d = 40 · 0.25 = 10 N · m (convert cm to m).
2) F = M / d = 6 / 0.75 = 8 N; at 15 cm: F = 6 / 0.15 = 40 N — the arm is 5 times shorter, so the force must be 5 times larger.
3) d = l · sin 30° = 0.5 · 0.5 = 0.25 m; M = 40 · 0.25 = 10 N · m. A perpendicular force would give 20 N · m: the slanted force loses half of its arm.

Sign up free to keep reading

The rest of the lesson, the quiz and your notes open with an Educora account. Signing up takes a minute, and your progress is saved on all your devices.

Two conditions of equilibrium and the rule of moments

For a rigid body to stay in equilibrium it must start neither moving forward nor rotating. So two conditions must hold at the same time:

ΣF = 0ΣM = 0

Where

ΣF
vector sum (resultant) of all forces acting on the body — the first condition
ΣM
algebraic sum of the moments of all forces about any axis — the second condition

For a body in equilibrium you may take moments about any point. The most convenient one is where an unknown force acts: its arm is zero, so it drops out of the equation.

A lever is a rigid body that can turn about a fixed pivot. If the pivot lies between the forces, it is a lever of the first kind (scissors, an equal-arm balance); if both forces are on the same side of the pivot, it is a lever of the second kind (for example, a wheelbarrow). For a weightless lever the second condition becomes the rule of moments:

OF₁F₂d₁d₂
Rule of moments: F₁ · d₁ = F₂ · d₂ — the short arm carries the large force, the long arm the small one.
F₁ · d₁ = F₂ · d₂F₁ / F₂ = d₂ / d₁F₁ · d₁ = F₂ · d₂F₁ / F₂ = d₂ / d₁

Where

F₁, F₂
forces that try to turn the lever in opposite directions, in N
d₁, d₂
their arms, in m

Rule of moments: a lever is in equilibrium when the clockwise moments equal the anticlockwise moments. The forces are inversely proportional to their arms. If the lever’s own weight is given, it acts at the centre of gravity (the middle of a uniform lever).

Example 2: lever problems

Problem

1) A 600 N load hangs from the 0.2 m short arm of a lever; the long arm is 1.2 m. What vertical force at the end of the long arm keeps the lever in equilibrium?
2) A uniform lever of mass 2 kg and length 1 m rests on a pivot 25 cm from its left end. What mass must hang from the left end to keep the lever horizontal?

Show solutionHide solution

Solution

1) F · 1.2 = 600 · 0.2 → F = 600 · 0.2 / 1.2 = 100 N: a sixfold gain in force.
2) The lever’s weight of 20 N acts at its middle, 50 − 25 = 25 cm to the right of the pivot. The load’s arm is also 25 cm: m · 10 · 0.25 = 20 · 0.25 → m = 2 kg.

Example 3 (multiple choice): which way does the lever turn?

Problem

A weightless lever can turn about the pivot O. A vertical downward force of 6 N acts 2 m to the left of the pivot, and a vertical downward force of 5 N acts 3 m to the right of it. The lever:
A) turns clockwise B) turns anticlockwise C) stays in equilibrium D) slides to the left on the pivot E) slides to the right on the pivot

Show solutionHide solution

Solution

Compare the moments, not the forces: the left force turns the lever anticlockwise, M₁ = 6 · 2 = 12 N · m; the right force turns it clockwise, M₂ = 5 · 3 = 15 N · m.
15 > 12 → the lever turns clockwise (A).
Option B is chosen by those who compare forces (6 N > 5 N).

Example 4 (multiple choice): a beam on two supports

Problem

A uniform beam 2 m long with a mass of 10 kg rests horizontally with its ends on two supports. A 20 kg load is placed 0.5 m from the left end. Find the forces with which the left and right supports act on the beam (g = 10 m/s²).
A) 150 N; 150 N B) 200 N; 100 N C) 100 N; 200 N D) 150 N; 50 N E) 250 N; 50 N

Show solutionHide solution

Solution

Four forces act on the beam: its weight of 100 N (at the middle), the load’s weight of 200 N, and the support forces Fleft and Fright.
Moments about the right support (Fright drops out): Fleft · 2 = 100 · 1 + 200 · 1.5 = 400 → Fleft = 200 N.
First condition: Fleft + Fright = 300 N → Fright = 100 N. Answer: B.
Check about the left support: Fright · 2 = 100 · 1 + 200 · 0.5 = 200 → 100 N ✓. Option D comes from forgetting the beam’s own weight, option C from swapping the supports.

Example 5 (coded answer): where is the pivot?

Problem

Vertical downward forces of 10 N and 50 N act at the ends of a 1.2 m weightless lever, which is in equilibrium. Calculate, in centimetres, the distance from the pivot to the point where the 10 N force acts.

Show solutionHide solution

Solution

Let the distance be x: 10 · x = 50 · (1.2 − x) → 60x = 60 → x = 1 m.
Check: 10 · 1 = 50 · 0.2 = 10 N · m ✓.
The code on the answer sheet is 100.

Centre of gravity and types of equilibrium

The resultant of the gravity forces acting on all particles of a body is applied at one point — the centre of gravity. For a uniform rod it is at the middle, for a uniform ball or disc at the centre, for a rectangular plate where the diagonals cross. The centre of gravity may even lie outside the body (a ring, a boomerang). For a system of two bodies:

xc = (m₁x₁ + m₂x₂) / (m₁ + m₂)xc = (m₁x₁ + m₂x₂) / (m₁ + m₂)

Where

xc
coordinate of the centre of gravity
m₁, m₂
masses of the bodies
x₁, x₂
coordinates of the bodies (of their centres of gravity)

This is the rule of moments itself: about the centre of gravity the moments of the gravity forces add up to zero, so the system balances when supported at this point.

Example 6: where is the centre of gravity?

Problem

1) Small balls of 1 kg and 2 kg are fixed at the ends of a 60 cm weightless rod. How far from the 1 kg ball is the centre of gravity?
2) A 1 kg load is attached to one end of a uniform rod of mass 3 kg and length 1 m. How far from the load is the centre of gravity?

Show solutionHide solution

Solution

1) xc = (1 · 0 + 2 · 60) / (1 + 2) = 40 cm — closer to the heavier ball.
2) The rod’s mass is treated as concentrated at its middle (0.5 m): xc = (1 · 0 + 3 · 0.5) / (1 + 3) = 0.375 m.
  • Stable equilibrium: tilt the body slightly and it returns; its centre of gravity is as low as possible (a hanging body, a ball at the bottom of a bowl).
  • Unstable equilibrium: after a small tilt the body moves further away; its centre of gravity is at the highest point (a ball on top of a dome, a pencil standing on its tip).
  • Neutral equilibrium: the body stays in equilibrium in any new position; the height of its centre of gravity does not change (a ball on a level table, a wheel on an axle through its centre of gravity).

A body standing on a base (a box, a bus, the Leaning Tower of Pisa) does not topple as long as the vertical line through its centre of gravity passes inside the base. The wider the base and the lower the centre of gravity, the more stable the body.

Pulleys

A pulley is a grooved wheel that turns on an axle, with a rope running in the groove. A fixed pulley has its axle fastened: it acts as an equal-arm lever (both arms equal the radius), so it gives no gain in force and only changes the direction of the force (F = P). A movable pulley rises together with the load: its pivot is at one side of the rope, so it is a lever of the second kind with arms r and 2r — it halves the force, but the free end of the rope travels twice as far.

PF = Pfixed pulleyF = P/2Pmovable pulley
A fixed pulley changes the direction of the force, a movable pulley its size.
F = P / ns = n · hF = P / ns = n · h

Where

F
force applied to the free end of the rope, in N
P
weight of the load (together with the movable pulleys), in N
n
number of rope segments holding up the load: n = 1 for a fixed pulley, n = 2 for one movable pulley
s, h
distances moved by the rope’s end and by the load, in m

Friction and the rope’s weight are neglected. A block and tackle (a system of pulleys) reduces the force n times, while the end of the rope travels n times farther.

Example 7: lifting loads with pulleys

Problem

1) A load weighing 400 N is lifted steadily with a movable pulley. What force is applied to the rope? How much rope must be pulled to raise the load by 3 m?
2) A movable pulley has a mass of 2 kg and the load 18 kg. What force is needed?
3) In a block and tackle the load hangs on 4 rope segments (n = 4). Find the force needed to lift a 1200 N load and how far the rope’s end moves when the load rises 0.5 m.

Show solutionHide solution

Solution

1) F = 400 / 2 = 200 N; s = 2 · 3 = 6 m.
2) The pulley rises with the load: F = (180 + 20) / 2 = 100 N (not 90 N).
3) F = 1200 / 4 = 300 N; s = 4 · 0.5 = 2 m. In every case F · s = P · h: there is no gain in work.

The inclined plane, the golden rule of mechanics and efficiency

Instead of lifting a load straight up through a height h, you can pull it along an inclined plane of length l. All simple machines share one law: none of them gives a gain in work. Whatever we gain in force, we lose in distance — this is the golden rule of mechanics.

F · l = P · hF = P · h / l = P · sin αF · l = P · hF = P · h / l = P · sin α

Where

F
force pulling the load steadily along the plane (no friction), in N
l, h
length and height of the inclined plane, in m
P
weight of the load, P = mg, in N
α
angle between the plane and the horizontal, sin α = h / l

The golden rule for an ideal (frictionless) inclined plane: the work F · l equals the work P · h needed to lift the load straight up. The longer (gentler) the plane, the smaller the force.

Example 8: the golden rule

Problem

1) What force is needed to pull a 1000 N load steadily up a smooth inclined plane 5 m long and 1 m high?
2) A 60 kg load is pulled up a smooth plane inclined at 30°. What is the force?
3) A lever lifts a 500 N load by 4 cm while the point where the force acts moves down 20 cm. Without friction, what is the force?

Show solutionHide solution

Solution

1) F = P · h / l = 1000 · 1 / 5 = 200 N — a fivefold gain, but the path is five times longer.
2) F = mg · sin 30° = 600 · 0.5 = 300 N.
3) F · 20 = 500 · 4 → F = 100 N: you do not need the lever’s arms, the ratio of the distances is enough.

A real machine has friction, and the pulley, rope or lever has its own weight. So the total (input) work we do is larger than the useful work needed to lift the load. How good a machine is shows its efficiency:

η = Wu / Win · 100% = P · h / (F · s) · 100%η = Wu / Win · 100% = P · h / (F · s) · 100%

Where

η
efficiency
Wu
useful work: Wu = P · h = mgh, in J
Win
total work: Win = F · s; s is the distance moved by the point where the force acts (l on an incline, 2h for a movable pulley), in J

Always η < 100%: the golden rule holds only for an ideal machine. For the same useful work, the lower the efficiency, the larger the force needed.

Example 9: calculating efficiency

Problem

1) A 100 kg load is pulled steadily up an inclined plane 4 m long and 1 m high with a force of 400 N. Find the efficiency.
2) A 40 kg load is lifted 3 m with a movable pulley; a force of 250 N is applied to the rope. What is the efficiency?

Show solutionHide solution

Solution

1) Wu = mgh = 1000 · 1 = 1000 J; Win = F · l = 400 · 4 = 1600 J; η = 1000 / 1600 · 100% = 62.5%.
2) Wu = 400 · 3 = 1200 J; the rope’s end moves 2 · 3 = 6 m: Win = 250 · 6 = 1500 J; η = 1200 / 1500 · 100% = 80%. Taking s = h gives η = 160% — impossible, which exposes the mistake.

Example 10 (coded answer): force from efficiency

Problem

A 30 kg load is raised to a height of 1.5 m along an inclined plane with an efficiency of 75%. The plane is 5 m long. Calculate, in newtons, the force that pulls the load steadily along the plane (g = 10 m/s²).

Show solutionHide solution

Solution

Wu = mgh = 300 · 1.5 = 450 J.
Win = Wu / η = 450 / 0.75 = 600 J.
F = Win / l = 600 / 5 = 120 N.
The code on the answer sheet is 120.

Interactive

Loading simulation…
The examples’ numbers are set. In the lever the unknown is F₁: holding a 600 N load on the 0.2 m arm takes 100 N at the end of the 1.2 m arm (Example 2); change d₁ and watch how the force changes. For the block and tackle see on the F–n curve how the force falls as n grows; for the incline look at the F–l curve. The efficiency formula gives the 62.5% of Example 9.
Check yourself
  1. 1.A 25 N force with an arm of 0.4 m has a moment of N · m.
  2. 2.A lever has arms of 0.3 m and 0.9 m; a 90 N load on the short arm is balanced by N on the long arm.
  3. 3.Lifting a 300 N load with a movable pulley needs a force of N.
  4. 4.If the useful work is 300 J and the total work 400 J, the efficiency is %.

Remember

  • Moment of force M = F · d; the arm is the shortest distance from the axis to the line of action.
  • Equilibrium: ΣF = 0 and ΣM = 0; for a lever F₁ · d₁ = F₂ · d₂.
  • In stable equilibrium the centre of gravity is at its lowest, in unstable at its highest; in neutral equilibrium its height does not change.
  • A fixed pulley only changes the direction of the force; a movable pulley halves the force but doubles the rope’s distance.
  • Golden rule: no simple machine gives a gain in work (F · s = P · h); the efficiency η = Wu / Win · 100% is always below 100%.
Spotted a mistake or something inaccurate in this lesson?

Check yourself

12 questions. Every correct answer earns XP.

Question 1 / 12

Question 1 / 12. What is the SI unit of the moment of a force?